Pagebuilder
Moderator: peterZ
Pagebuilder
I installed the mathlab runtime and downloaded the version of pagebuilder that runs on Vista, but I still get the following error:
"This application has failed to start because mclmcrrt70.dll was not found."
Any ideas?
Thanks.
"This application has failed to start because mclmcrrt70.dll was not found."
Any ideas?
Thanks.
Re: Pagebuilder
Download Links:
Pagebuilder for XP:
http://danreetz.com/book_scanner/PgBldr2_XP.zip
Pagebuilder for Vista:
http://danreetz.com/book_scanner/PgBldr2_Vista.zip
Pagebuilder for XP with JPG output:
http://danreetz.com/book_scanner/PgBldr2_JPEG_XP.zip
Matlab Component Runtime (175MB):
http://danreetz.com/book_scanner/MCRInstaller.exe
Editor's note: removed redirectingat URLs. I'm investigating the cause.
Pagebuilder for XP:
http://danreetz.com/book_scanner/PgBldr2_XP.zip
Pagebuilder for Vista:
http://danreetz.com/book_scanner/PgBldr2_Vista.zip
Pagebuilder for XP with JPG output:
http://danreetz.com/book_scanner/PgBldr2_JPEG_XP.zip
Matlab Component Runtime (175MB):
http://danreetz.com/book_scanner/MCRInstaller.exe
Editor's note: removed redirectingat URLs. I'm investigating the cause.
- daniel_reetz
- Posts: 2812
- Joined: 03 Jun 2009, 13:56
- E-book readers owned: Used to have a PRS-500
- Number of books owned: 600
- Country: United States
- Contact:
Re: Pagebuilder
Hmm, that's troubling. That's the error you get when the MCR isn't installed. I'll get you the new version (I've emailed Aaron) and let's try that before doing anything else. It only takes a minute to compile, if he checks his email it should get done today.
- daniel_reetz
- Posts: 2812
- Joined: 03 Jun 2009, 13:56
- E-book readers owned: Used to have a PRS-500
- Number of books owned: 600
- Country: United States
- Contact:
Re: Pagebuilder
BTW, Try searching your machine for "mclmcrrt70.dll" -- it would be interesting to see if it actually shows up somewhere.
- daniel_reetz
- Posts: 2812
- Joined: 03 Jun 2009, 13:56
- E-book readers owned: Used to have a PRS-500
- Number of books owned: 600
- Country: United States
- Contact:
Re: Pagebuilder
PS. What's with the weird "Redirectingat" links?
- daniel_reetz
- Posts: 2812
- Joined: 03 Jun 2009, 13:56
- E-book readers owned: Used to have a PRS-500
- Number of books owned: 600
- Country: United States
- Contact:
Re: Pagebuilder
PPS. Totally stupid question... have you restarted your machine since installing the MCR?
- daniel_reetz
- Posts: 2812
- Joined: 03 Jun 2009, 13:56
- E-book readers owned: Used to have a PRS-500
- Number of books owned: 600
- Country: United States
- Contact:
Re: Pagebuilder
Still waiting to hear back from Aaron, I'll check with him today.
- daniel_reetz
- Posts: 2812
- Joined: 03 Jun 2009, 13:56
- E-book readers owned: Used to have a PRS-500
- Number of books owned: 600
- Country: United States
- Contact:
Re: Pagebuilder
I just got this link from Aaron, I think it is the right version though again, he hasn't emailed me back on that.
http://www.psych.ndsu.nodak.edu/aclarke/PgBuilder2.zip
http://www.psych.ndsu.nodak.edu/aclarke/PgBuilder2.zip
-
- Posts: 14
- Joined: 04 Mar 2014, 00:52
Re: Pagebuilder
hey jradi
i have the exact same prob
have you got the program running? if so can you please explain what you did in fairly simple terms.
I have installed matlab runtime + pb software, have restarted computer, then tried opening pb software but no luck. is that the right sequence or should i be doing something special with matlab to make it work.
thanks
i have the exact same prob
have you got the program running? if so can you please explain what you did in fairly simple terms.
I have installed matlab runtime + pb software, have restarted computer, then tried opening pb software but no luck. is that the right sequence or should i be doing something special with matlab to make it work.
thanks
Re: Pagebuilder
I haven't played with it in a while, but I'll try the new version.
As for the redirect links, I just copied and pasted them from the instructables site, I thought You had written them that way!
As for the redirect links, I just copied and pasted them from the instructables site, I thought You had written them that way!